How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with a keyless entry system built into. This key typically resembles an electronic remote and can be exchanged with a brand new one from a Kia dealer or locksmith.

Key fobs are prone to malfunction for a variety of reasons, such as the battery of the coin is dead, worn buttons or buttons, signal interference, water damage and a damaged receiver module. Here are some suggestions on how to get your Kia Sportage replacement key back to working.

how much is a replacement car key kia do you replace the remote key or the smart key?

The battery in your 2013 kia sportage key fob programming's intelligent key will eventually need to be replaced, regardless of whether it's a remote key as well as a push-to start key or a normal metal key that doesn't contain transponder. This is especially relevant if your vehicle shows a message that states the smart or remote keys are in poor condition.

This is a relatively easy process. To replace the key fob battery remove the mechanical key from the hole in the back of the key fob. Then break the cover. Inside the key fob, there will be the small screw that holds the battery in the correct position. Remove the old battery by detaching the screw using the help of a small screwdriver. Insert the new battery and then close the slit on the key fob.

Once the key fob has a fresh battery check it by pressing the locks and unlock buttons. It's okay If the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder keys made of metal), do not need programming. If you need to reprogramme your key, you'll have to write down the key code's number on the key code tag.

How do you replace the battery?

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a sign that the battery needs to be replaced. A low battery may also cause other issues like the check engine light turning on or the engine not cranking. It is quite simple to replace key fob batteries using just a few simple tools.

Before starting the process before beginning the process, ensure that your vehicle is off and all doors are shut. Locate the small plastic piece that is on the bottom of your key fob, and play with it until a metallic key slips out. Then, you can put the key into the driver's door handle to unlock your car.

To replace the battery on the key fob, remove the cover at the rear. Utilize a plastic plier tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery to ensure its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the contacts of the metal.

Once the new battery is installed after which you turn the key fob off and then turn it on in the ignition repeatedly until the door locks cycle. You can then test the 2017 kia sportage key fob programming's key fob once more to ensure it's working as intended.

How do I replace a smart key

There is a possibility of having the standard keyfob or Smart Key based upon the model of Kia Sportage. The difference between these is that the smart key is equipped with an incredibly small key blade hidden within it, whereas the standard fob does not. Both key fobs have batteries that will eventually require replacement. This is an easy process that takes less than two minutes.

Make sure you turn off your Kia and sit on a flat or well-lit surface prior to when you begin. Also, keep in mind that there are small parts inside the fob that can fall out if not cautious.

The first step is to locate the small release button on the lower backside of your fob. It will be either an oval silver button or a rectangular slot. After pressing this button, the mechanical key blade will appear and you will be able to open the key fob.

Once you have the key fob opened then you can remove the old battery, and replace it. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. After you've finished it should be possible to lock or unlock your vehicle using your key fob - even if your engine isn't running!

How do you replace a mechanical key

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car simply by pressing the button. As with all devices that is used, the Kia key fob can occasionally have problems. There are ways to address these issues and keep your key fobs working for the duration of.

A dead or drained battery is one of the most frequent problems. This could cause your device to stop working or work intermittently. If this happens try replacing the battery with a fresh new one.

If this doesn't solve the issue, use a standard flathead screwdriver to push the fob's plastic casing open. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed and replaced, you can replace it with a brand new battery.

After the new battery has been put installed, close and unlock the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the fob to make sure it's functioning correctly. Contact a dealer or a locksmith to fix the issue in the event that the fob is not working. To avoid lockouts in the future, ensure you purchase an emergency key that will be able to work with all door and trunk cylinders.